So I have a fresh Epoch 1.0.2.3 server setup, and have been working on getting Sarge AI installed. I have followed the directions listed, though I'm stuck on a restriction error from BattlEye.
Steps taken in order, as follows -
1. Under MPMissions > DayZ_Epoch_11.Chernarus, I created a new 'addons' folder and moved SHK-POS, SARGE, and UPSMON into the folder.
2. Edit init.sqf under MPMissions > DayZ_Epoch_11.Chernarus, nd add the provided lines at the very end.
3. Edit description.ext and add the provided line at the very end.
4. Use PBOViewer, and unpackaged dayz_server.pbo that's located under @DayZ_Epoch_Server > addons directory. Then make the provided changes to server_cleanup.fsm.
5. Didn't touch SAR_config.sqf since those were set to false already.
6. Edited scripts.txt under instance_11_Chernarus > BattlEye, and the lines provided were not listed there so I added both to this file.
Restarted the server, and everything goes smoothly until you get to Requesting Server Authentication, which now takes between 60-120 seconds to load which without these changes, it normally went through instantly. Once that finally loads through, I get a BattlEye Restriction #0 and am kicked.
Below is from the log, edited out the GUID and IP with xxxx.
- - -
21:00:04 BattlEye Server: Initialized (v1.177)
21:00:04 Host identity created.
21:00:42 Necro uses modified data file
21:00:42 BattlEye Server: Player #0 Necro (xxxx) connected
21:00:42 Player Necro connecting.
21:00:42 Mission DayZ Epoch Chernarus read from directory.
21:00:43 Player Necro connected (id=95305030).
21:00:43 BattlEye Server: Player #0 Necro - GUID: xxxx (unverified)
21:00:43 BattlEye Server: Verified GUID (xxxx) of player #0 Necro
21:00:46 Roles assigned.
21:00:46 Reading mission ...
21:00:54 Mission read.
21:01:39 Game started.
21:02:04 Player Necro kicked off by BattlEye: Script Restriction #0
21:02:04 Player Necro disconnected.
Thank you in advance. I'm sure it's something simple I'm missing or may have done incorrect. Server works fine without Sarge AI. Only breaks when I make the edits.
Question
Hummuluis
Hello all,
So I have a fresh Epoch 1.0.2.3 server setup, and have been working on getting Sarge AI installed. I have followed the directions listed, though I'm stuck on a restriction error from BattlEye.
Steps taken in order, as follows -
1. Under MPMissions > DayZ_Epoch_11.Chernarus, I created a new 'addons' folder and moved SHK-POS, SARGE, and UPSMON into the folder.
2. Edit init.sqf under MPMissions > DayZ_Epoch_11.Chernarus, nd add the provided lines at the very end.
3. Edit description.ext and add the provided line at the very end.
4. Use PBOViewer, and unpackaged dayz_server.pbo that's located under @DayZ_Epoch_Server > addons directory. Then make the provided changes to server_cleanup.fsm.
5. Didn't touch SAR_config.sqf since those were set to false already.
6. Edited scripts.txt under instance_11_Chernarus > BattlEye, and the lines provided were not listed there so I added both to this file.
Restarted the server, and everything goes smoothly until you get to Requesting Server Authentication, which now takes between 60-120 seconds to load which without these changes, it normally went through instantly. Once that finally loads through, I get a BattlEye Restriction #0 and am kicked.
Below is from the log, edited out the GUID and IP with xxxx.
- - -
21:00:04 BattlEye Server: Initialized (v1.177)
21:00:04 Host identity created.
21:00:42 Necro uses modified data file
21:00:42 BattlEye Server: Player #0 Necro (xxxx) connected
21:00:42 Player Necro connecting.
21:00:42 Mission DayZ Epoch Chernarus read from directory.
21:00:43 Player Necro connected (id=95305030).
21:00:43 BattlEye Server: Player #0 Necro - GUID: xxxx (unverified)
21:00:43 BattlEye Server: Verified GUID (xxxx) of player #0 Necro
21:00:46 Roles assigned.
21:00:46 Reading mission ...
21:00:54 Mission read.
21:01:39 Game started.
21:02:04 Player Necro kicked off by BattlEye: Script Restriction #0
21:02:04 Player Necro disconnected.
Thank you in advance. I'm sure it's something simple I'm missing or may have done incorrect. Server works fine without Sarge AI. Only breaks when I make the edits.
Link to comment
Share on other sites
1 answer to this question
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now